Tool Maker Vise of Plugs Type VA/VB |
- The tool maker vise is made by high carbon steel, hardened by heat treatment and machined by precise grinding
- It can maintain high precision either in horizontal and vertical position
- VA-type tool maker vise applies pin to adjust the clipping distance between vise and slippery block
- VB-type tool maker vise holds all functions of VA-type one, plus that it can adjust the clipping distance without disassembling any part from it
|
Tool Maker Vise of Plugs & Vbig Type VB |
Super Precision Tool Maker Vise VC
|
Tool Maker Vise of Screw Type VD |
Tool Maker Vise of Screw Type VE
|
Tool Maker Vise VF |
- The VF tool maker vise applies new structure design that can hold certain angle of up-lifting force
- Easy to adjust the distance between vise and slippery block and facilitate to operation
|
Tool Maker Vise Of Small Type V1 |
- Micro tool maker vise is applied to clip tiny work pieces, or assist large vise to make two-way compound clipping and ensure the clipping precision
|
Sine Vise SV |
- Except holding the advantages of tool maker vise, the sine vise also can clip work piece by various angles under sine theory to check and cut the work piece
- The adjustable angle range is 0~46°, sine gauge conversion table is attached to product for gauge selection.
|
Sine Vise Of Screw Type V |
|
Precision Vise Of Stainless Steel VST10 |
- The micro tool maker vise is applied to clip tiny work pieces; it is made by stainless steel Easy to maintai
- The levelling and verticality are lower than 0.004mm
- Suitable to clip tiny work pieces of various sorts
|
Precision Vise Of Stainless Steel VST25
|
- The vise is made by stainless steel, rust-free
- Easy to maintain and with high precision
|
Precision Vise Of Stainless Steel VBST30 |
- The stainless steel vise and slippery block are formed by de-wax casting process Proceeded by hardening and grinding process
- Anti-corrosion
- High precision
- Easy to maintain it
|
Precision Vise Of Stainless Steel VBST200-300 |
- The vise is made by stainless steel
- Rust-free
- Easy to maintain
- High precision
|
Tool Maker Vise-Edw Type WST50 |
Tool Maker Vise-Edw Type WST100-150
|
Both vise and slippery block are made by stainless steel; Good anti-corrosion capability
|
Electrode Holders Stainless EH20 |
- The entire vise set is made by stainless steel Easy to maintain it Vise can change either horizontal or vertical work direction Facilitate to clip pole copper High working precision preserved
|
Electrode Holders Stainless EH50
|
- Made by stainless steel Screw design is easier to operate Can clip work piece on both horizontal and vertical directions
|
Universl Facing And Boring Head BAM |
- It is construction with precision parts
- Freedom of selection feeding quantity
- Auto feed and stop
- It can move forward backward
- Processing range from 5mm to 250mm
|
Universal Boring And Facing Master Head BAH |
- It is construction with precision parts
- Freedom of selection feeding quantity
- Auto feed and stop
- Processing range from 5mm to 250mm
|
Boring Head BA |
- Easily to operate convenient use push handle can replaced at any moment suitable to any type of drilling machine, rotary armed drill, boring machine and complex machines etc
- Processing range: minimum boring diameter of hole 10mm; maximum boring diameter hole 250mm
- Feeding quantity cutter of every scale of 0.01mm. Will proceed 0.02mm
- Quality guarantee, teeth or screw finished with SCM steel rubbed after heat treatment
- Absolutely guarantee the durability for wearing and the accuracy
|
Boring Head BB |
- Easily to operate convenient use push handle can be replaced at any moment suitable to any type of drilling machine, rotary armed drill, boring machine and complex machines etc
- Processing range: minimum boring diameter of hole 10mm; maximum boring diameter hole 250mm
- Feeding quantity cutter of every scale of 0.01mm. Will proceed 0.02mm
- Quality guarantee, teeth or screw finished with SCM steel rubbed after heat treatment
- Absolutely guarantee the durability for wearing and the accuracy
|
Boring Head BC3 |
- Easily to operate convenient use push handle can replaced at any moment suitable to any type of drilling machine, rotary armed drill, boring machine and complex machines etc
- Processing range: minimum boring diameter of hole 10mm; maximum boring diameter hole 250mm
- Feeding quantity cutter of every scale of 0.01mm. Will proceed 0.02mm
- Quality guarantee, teeth or screw finished with SCM steel rubbed after heat treatment
- Absolutely guarantee the durability for wearing and the accuracy
|
Boring Head BC2 |
- WORK RANGE
- Mini boring diameter 10mm
- Maximum boring diameter Ø180mm
- Maximum boring depth 50mm
|
Boring Head BC2 |
- Here is a small boring head that will be in constant demand in any shop
- The wide base bearing surface that assures maximum rigidity even when the bat holder is in off-set position
- This wide base designs a recent criterion
- Innovation that increase surfaces by 50% over the older models
- A choice of 1/2″ double hole bar holder with a 1/2″ cross hole is available
- The unit has a 7/8-20 threaded back and also features a direct reading dial screw
|
Boring Head BC3 |
- Here is sturdy unit of extended boring range
- Capable of peeling off heavy roughing cuts as well as a tool extreme sensitivity
- The use of wide base bar holder, resting securely on the body, eliminates the need for a separate side plate. You will note this has now become an integral part of the body
- The direct reading adjusting screw is ground after hardening and a have threaded backs for use with a variety of shanks
- This model takes reading and a adjustments of .0005 or less
- All criterion boring heads plainly marked dial face in non-reflecting satin chrome allows easy a 1-1/2″-18 threaded shank
|
Boring Head BC4
|
- This is bigger boring head which can be put on a large machine to process more as you want
- The radius of boring hold can reach on about Ø400mm by a boring bar of 16mm.
|
Boring Head Shank |
- Type-A taper stem is applied to type-BA boring heads
- Type-B taper stem is applied to type-BB, BAM & BAH boring heads
- Type-C taper stem is applied to type-BC2, BC3 & BC4 boring heads
|
Tangimtic Dresser TDA |
- Type-R trimmer is applied to plane grinder to trim type-R grinding wheel in a diameter of 8″ and smaller
- The work scope includes:
- Raised type: R=0-40R
- Concaved type : R=0-90R
|
Radius and Angle Dresser TDB |
- The trimmer is applied to plane grinder to trim grinding wheels, 10″Ø and smaller, under any angle, and form raised/concaved R
- The work scope is:
- Trim raised R in the range of 0.8-40R
- Trim raised R in the range 0-40R
- 40mm stroke in both left/right directions
|
Universal Wheel Dresser TDC |
- Extremely precise grinding wheel trimmer
- Applied to trim any angle or uneven of grinding wheel
- Trim the grinding wheel installed in cylinder grinder
- No need to move the standard head to adjust trimming angle
- The angle is formed by constantly pushing the handle after round arc is fixed
- Can trim precisely, rapidly and repeatedly
- Can make clean and precise trim to grinding wheel outline, no repeat mark required
- No perfect compound angle and arc can be made without using this equipment
- Precise and sharp outline scheme
- 003 precision can be acquired within 180 degrees of both raised/ concaved R
- Range of raised R: 0R~2R
- Range of concaved R: 0.8R~9R
|
Visual Radius Angle Dresser TDD |
- The optic-transparency universal wheel trimmer is mainly applied to trim the combination of angle and arc of grinding wheel equipped to plane grinder and universal tool grinder
- By means of 4X optic lens
- Operator can observe the contacting status of cutting pen tip and grinding wheel surface
- By using blocking gauge and YCT magnetic sine gauge
- The trimming precision is extraordinarily outstanding
|
Precision Duplex Dresser TDE |
- The two-side trimmer has applied the two-direction turning design to trim both sides of grinding wheel by concurrent feeding
- It has applied excellent diamond cutter and suitable trimming wheel to work
- The thinnest trimming thickness of grinding wheel is 0.2mm.
|
Diamond CBN Flat Wheel Truer TDF |
- The design grinding wheel uses of diamond grinding wheel and trimmer and combines turning difference to trim grinding wheel work piece
- It can acquire precise and stable trimming result in response.
|
Angle Sine Dresser 50A |
- The trimming range is for any angle within 0~60°
- The maximum moving stroke is 65mm
- Reliable structure and high precision
- After the slippery block is removed
- The trimmer can be applied as a sine gauge
|
Angle Sine Dresser 50B
|
- Grinding wheel angle trimmer
- The improved positioning locking device is convenient in operation
- The maximum moving stroke is 60mm
- After the slippery block is removed, the trimmer can be applied as a sine gauge
|
Punch Grinder PG |
- The punch grinder is the convenient tool to revise or produce punch head
- 005mm or less coaxial offset can be reached in plane grinder work without an adjustment required
- The available clipping and grinding range is Ø3~Ø30
- The extruded grinding length is within 35mm
|
Punch Grinder PGS |
- Grinder for small punches
- Applied to clip and grind Ø1.5~Ø8 punch products
- The clipping precision is within 0.005mm
|
Punch Grinder PGSS |
- The mini punch grinder is exclusively designed to machine the outer diameter of tiny punches
- Since the configuration is precise and accurate, therefore, if working with suitable measuring elements
- It can be a tester of coaxial offset and roundness
- Minimum outer diameter under grinding is Ø0.5mm
|
Motor Punch Grinder PGM |
- Motor-driven roller, easy in operation
- Operator can pay attention to operate the feeding of grinding wheel
- No need to calibrate center position
- Punch is inserted in roller and thus the concentric circles can be derived without any adjustment made
- After grinding wheel is formed, it can machine punch pins of any special forms
- Can grind long injection pins and punches
|
Punch Former (one way) PS |
- Punch former suitable to be applied in plane grinder by forming standard punch head to desired shape
- The best tool for machining punch heads of various shapes
- Centrally penetrated to the machine body
- Suitable to machine punches or injection pins of length
- R-type forming rod is attached to perform concaved-R or raised-R trim of grinding wheel
- Can make 24 partition equally (15-degree dividing), angle is fixed and the partition tolerance is within ±10 seconds; also, it can apply the sine theorem to set up any angle by associating different gauges
- Main body is integrated into one piece with reliable precision
- PSP is optional parts, applied to trim the angle of grinding wheels
|
Punch Former (two way) PB |
- Punch former is suitable to be applied in plane grinder by forming standard punch head to desired shape
- The tool for machining punch heads of various shapes
- Can make both horizontal and vertical adjustment, able to adjust and set up all sorts of complicate shapes
- R-type forming rod is attached to perform concaved-R or raised-R trim of grinding wheel
- Can make 24 partition equally (15-degree dividing), angle is fixed, and the partition tolerance is within ± 10 second; also, it can apply the sine theorem to set up any angle by associating different black gauges
- Main body is integrated into one piece with reliable precision
|
3-Jaws Punch Former PSA |
- Three-piece type of punch maker is designed particularly for round pieces with diverse dimensions
- The maximum hole size for the main body of three-piece clipping head to go through is Ø16
- Allowable holding size of positive claw is Ø2- Ø30mm
- Allowable holding size of negative claw is Ø30- Ø70mm
|
ER Collet Punch Former PSB |
- The cylinder-type punch maker is designed exclusively to machine round work pieces in unity size and massive quantities
- Use type ER32 cylinder clipping head, which is attached with 7 different pieces of cylinder clips (Ø4, 6, 8, 10, 12, 16, & 20)
- The cylinder-type punch maker can fast and stably to clip work piece; auto center-positioned, easy to operate
|
Matco Siene Dresser PSP |
- Specifically designed for unidirectional punch maker
- Enable to trim the angle of grinding wheel
|
Sine Plates SPS50 |
- SPS50 sine table is designed on particular for PS, PB, PSA, PSB punch maker
- The sine table applies sine angle theorem to combine the machining angle of punch maker, reaching the best precision level
|
Sine Bar Mertic S100 |
- Essential measuring gauge to the angle setting of forming grinder
- Guaranteed accuracy of sine gauge is within 0.005mm
|
Sine Bar Mertic S25-50 |
|
Magnetic Sine Bar MS50-100
|
- Install permanent magnet at bottom of sine gauge with dense magnetic flux density
- Applied to operate at machining tools and work pieces of various sorts
- Can precisely position any angle specified
|
Precision Square LS |
|
Precision Gauge Block |
- Block gauge is the measuring datum of length, applied to adjust, calibrate or inspect other measuring instruments, gauges or precise work pieces
- Apply alloy steel to produce block gauges, the surface hardness is no less than HRC64°, good wear-resisted ability is preserved
- Under special machining process, dimension accuracy is good and stable
|
Adjustable Angle Plates AP
|
Micro-Adjustable Angle Plate APM |
Angular measures from 0~60° |
Angle Level
|
- Apply double ring scale, allows reading out data at opposite direction, high accuracy is secured
- Can immediately measure level grade or any angle inclined
- Can adjust temporary level setting and measure the angle and level deviation immediately
- Magnetic rail is attached to bottom seat
- Able to demagnetize or reduce its field strength and elongate the applicable measuring length
|
A Pair Of V Blocks APV |
Precision Angle Plate LAP |
Precision Angle Block Set APA |
- Precision Angle Blocks
- A simplified, accurate and quick method for angle set-ups in tooling, production and in section
- Accuracy ±00001″ per inch.
- Lightly magnetized for better holding.
- Size 3″ long ×1/4″ thick.
- Ten block set complete with certification in fitted case
|
Precision Parallels Set APB |
- Material S50C
- ±10 Second Tolerance
- Hardness HRC50~55°
- All Ground Finish
|
Precision Parallels Set PPA |
- Material S50C
- Hardness HRC50~55°
- Precision: W×H±01L±0.5
- Accuracy:0.01mm
|
Precision Parallels Set PPB |
- Hardness HRC50~55°
- Precision: W×H±01L±0.5
- Accuracy:0.01mm
- Process: Four-side grinding
- 1 set includes 18 pcs
- Packed by plastic case
|
Precision Parallels Set PPC |
Precision Parallels Set PPD |
Hardness HRC50~55°
Precision: W×H±01L±0.5
Accuracy:0.01mm
|
Sine Plates 40-66-612 |
- Use sine theorem to make precision setting
- Applied to be a cutting fixture
- Lots of holes made on panel to fix work pieces
- Body surface hardness is HRC56~58° and fine grinded, the plane precision is within ±005mm
- Allowable angle working range is 0~46°
|
Magentic Sine Plate (coarse) 47-66M |
- The magnetic line interval of coarse sine magnetic table is 7.6 (1.5+6)
- Providing economic and easy usability
- The precision is within ±0.005mm
|
Magentic sine plates (fine) 47-66MS |
- The magnetic line interval of permanent magnet installed to fine sine magnetic table is 2.5 (1+1.5)
- Can supply powerful and dense magnetic force
- On particular suitable to fine work piece under machining process
- Allowable angle working range is 0~46°
|
Sine Plate With Fine Magnetic Chuck 47-66-612MSS |
- Height is lower than ordinary sine table
- Convenient in use
- 2.5 (1+1.5) dense magnetic line interval provides strengthened and concentrated magnetic force
- The locking device can exert compression force to wheel directly
- Precision isn’t influenced while fixing operation angl
|
Fine Adjustment Sine Plate With Magnetic Chuck |
- Easy to operate
- Merely turn the fine-tuning handle to adjust and fix operation angle
- 5 (1+1.5) dense magnetic line interval provide strengthened and concentrated magnetic force
- Have high precision and stability
- Precision is controlled within 0.003mm while operating within 0~60°
|
Powerful Angular Permanent Magnetic Chuck With Carbide
|
- Select work substance with weaker magnetic feature, for instance: tungsten carbonized
- Can work with large scale clipping disc owning permanent magnetic or electromagnetic force
|
Magnetic Induction Block GTA/GTB |
- Magnetism-free GTA-GTB that can be applied in any disk to generate magnetism after magnetic field is permeated
|
Magnetic V-Block GVA-GVB
|
- Permanent magnet is inserted in V slot that can attract plane or cylindrical work piece
- This product is applied on grinding machine or inspection bench
|
Magnetic V-Block GVC-GVD |
- Two pieces in one set that can be separately in use or combined together
- Applied to long work piece with magnetic capability
|
Magnetic V-Block GVE-GVF |
- Square shape design, magnetic force exerts on top, side and V-slut surface
- Precise verticality made; workable on horizontal or vertical position
- Applied to fixture
- Perform measurement or draw line
- V-slut surface can hold round or rod piece by magnetic force
|
Powerful Angular Permanent Magnetic Chuck |
- 50mm in thickness that is thinner than ordinary permanent magnet, the machining space is larger
- Panel metal is connected together, anti-corrosion secured
- High precision, hard to deform, applied to high-precision machining work
|
Powerful Angular Permanent Magnetic Chuck |
- 50mm in thickness that is thinner than ordinary permanent magnet, the machining space is larger
- The magnetic line interval is 2.5 (1+1.5), magnetic field distribution is uniform, suitable to small and thin work pieces
- Panel metal is connected together, anti-corrosion secured
- High precision, hard to deform, applied to high-precision machining work
|
Powerful Angular Permanent Magnetic Chuck |
- While switching over magnetic dish switch, the plane precision on the magnetic plane is unchanged
- The magnetic level interval is 2 (1+1), magnetic field distribution is uniform
- Suitable to small and thin work pieces
- Panel metal is connected together
- Able to withstand any corrosion made from cutting liquid
- Applied high-performance magnetite that can create powerful magnetic force and with small magnetic residual coefficient
- High precision and tiny deviation; conforming to high precision machining operation requirement
|
Round Permanent Magnetic Chuck |
- Suitable to normal work pieces making precise grinding process
- Can be installed on rotary grinding machine
|
Round Fine Pole Permanent Magnetic Chuck |
- Suitable to tiny or thinner pieces performing precise grinding process
- Can be installed on rotary grinding machine
|
Rotary Permanent Magnetic Chuck |
- Main body and rotary spindle are integrated into one piece, the rotation positioning is precise
- Panel metal is connected together, able to withstand any corrosion made from cutting liquid
- Bi-magnetic line interval design that can be applied to work pieces having varied size and thickness
- The magnetic line interval of coarse clipping disc is 11.2 (1.6+2+1.6+6)
- The magnetic line interval of fine clipping disc is 2 (1+1)
|
Handy Type Demagnetizer EDA |
- Operation condition is common
- Can be applied by putting on plane or by handhold
- Turn off 10 minutes after operating 90 minutes continually
- Auto thermal protection device preserved
|
Handy Type Demagnetizer EDB |
- Put the product on a plane and fix it in operation
- Applied to remove residual magnetic force of normal parts after machining process
- Can work continuously for a long time
|
OZ Milling Collet Chuck System |
- The box contains one cutter stem, one spanner and a set of spring cylinder clip
- Can select metric or British screw and collocate to 7 to 16 cylinder clip set
- Conform to the production precision defend in DIN6388
|
ER Milling Collet Chuck System |
- The box contains one cutter stem, one spanner and a set of spring cylinder clip
- Can select metric or British screw and collocate to 6 to 23 cylinder clip set
|
ER Spring Collet |
- Conform to the production precision defined in DIN6499
- Made by bearing steel with higher elasticity and operation lifetime
- ER11 has an expansion allowance of 0.5mm
- ER11, ER16, ER20, ER25, ER30 & ER40 commonly have an expansion allowance of 1mm
|
Mill Collet Chick-er Type |
- Main body is made by SCM-415 steel with heat treatment and grinded
- Screw has two options: Metric and British screw
|
BT Mill Collet Chick-er Type |
BT Face Mill Arbor |
Straight Shank Collet |
- Straight cylindrical stem suitable to clip small drilling or milling tools
- Outer diameter, taper and screw are under precise grinding process
- Nut is fastened directly, the rigidity and holding strength is outstanding
|
Drill Chucks |
- Directly turn to fasten handle
- Easy to operate and holding strength good
- High precision, taper hole can meet DIN specification
|
Precision Universal Vise |
|
Universal 3-Way Angle Milling Vise |
- Vise can make angle setting on three directions
- Seat can be positioned in 360°
- 0~90° positioned to perpendicular angle
- 0~45° positioned to side angle
|
K-Type Milling Vise VK |
- Body and V fixing slut is formed in one piece
- The rigidity is large and hard to deform
- Partition scale made at seat, main body can rotate 360° around on horizontal plane and fixed to operate
|
Ang-Fixed Milling Vise VG |
- Here is the right vise for use on all your tape controlled machine to tools
- What the vise doesn’t have is a coolant through
- This enables you to anchor a series of these vises snugly side-by-side on the machine bed. A number of similar parts can be clamped and machined at the same time
- With minimum center-to-center machining distance. Up goes your production rate, down goes costs
- Both sides are precision ground square to bottom and parallel with each other and so the vise can also be used at vertical position with its vise bed perfectly perpendicular to the machine table
- Can be replaced side-by-side on your N/C equipment
- Permits fast accurate multiple machining
- Sides ground
- The squareness of both sides within 0.01mm and parallelism within 0.02mm
- Keyways on bottom to steady jaw plate
|
Ang-Fixed Milling Vise VL |
|
Hydraulic Machine Vise HVA |
- Built-in hydraulic and pressure-adding design
- Instantly knock handle will change to pressure-adding feed automatically and show powerful holding strength
|
Two Way Hydraulic Machine Vise HVB |
- Hydraulic pressure: the pressure-adding design that can show powerful holding force
- Can apply inclined angle and plane rotation angle
|
Semi-Universal Dividing Head BS
|
- Made by FC30 high-strength casting iron
- Suitable to driller, miller or other special machines making simple fast partition task
- The direct partition disc can make fast partition to2, 3, 4, 6, 8, 12, & 24 pieces equally, or 2~380 unequal partition as work with honeycomb plate, 0~90° adjust the inclined angle
- Work with honeycomb plate to make uneven partition
- Work with miller to add gear making kinetic machining process
- Add three-piece clipping head to make spindle machining process
- Speed reduction ratio=1:40
|
Universal Dividing Head BS |
- Made by FC30 high-strength casting iron
- Suitable to driller, miller or other special machines making simple fast partition task
- The direct partition disc can make fast partition to2, 3, 4, 6, 8, 12, & 24 pieces equally, or 2~380 unequal partition as work with honeycomb plate, 0~90° adjust the inclined angle
- Work with honeycomb plate to make uneven partition
- Work with miller to add gear making kinetic machining process
- Add three-piece clipping head to make spindle machining process
- Speed reduction ratio=1:40
|
Horizontal And Vertical Rotary Table HV
|
Super Index Spacer
|
Universal Tilting Rotary Table |
- Made by FC30 high-strength casting iron
- Suitable to make universal inclined partition to miller, driller or other special machines, or make (24-division) fast partition
- The inclined angle of work bench is 0~90 degree, the partition angle is 0~360 degree
- Can coordinate to honeycomb plate performing uneven partition
- Speed reducing ratio is 1:90, 4 degrees per one turn of hand wheel
|
Clamping Kit |
- Applied to the T-slut of various machine workbenches, on particular for the use of fixing mold or fixtures plates
- Screw length is 25mm on both end of screw bolt; 24 pieces in total:
- Four pieces for 75, 100, 125, 150, 175 & 200mm (in metric unit), and 3″, 4″, 5″, 6″, 7″, & 8″ each (in British unit) each
- Six T-nuts
- Six fange nuts
- Six connecting head nuts
- Six teeth shaped plates
- Six teeth shaped pads
|
Work Stopper |
- Body is made by aluminum alloy that can be installed to ordinary machine
- Able to freely adjust height and angle; and positioned in any direction
|
Chamfering & Deburring Machine |
- Use sand-cloth wheel to make grind cutting; can cut back-angle on soft/hard material
- Applied to cut back-angle of hardened work pieces
- The cutting surface is fine and free from burr
|
Mechanical Edge Finder |
- Applied to measure the X and Y axle coordinates of work piece
- 4mm detector is available to measure tiny hole and slut
- Applied in 400-600 RPM of rotation
|
Optical Edge Finder |
- Can measure at stationary state
- Applied to measure the X and Y axle coordinates of work piece
- When detector touches work piece, alarm and red light flash will arise
- Tolerance between test stem and detector center is within 0.005mm
|
Universal Arm Magnetic Base |
- Mechanical driving; the detector can be easily adjusted toward any direction and as wish
- Mechanical driving, reliable performance, free from oil leak in hydraulic system
|
Ejector Pin Cutting Of Machine |
- Suitable to cut down mold, round pin and stainless steel products
- Cutting surface of heat treated material is smooth without burr
- Easy to apply, fast cutting, operation time is short
- Hard to get disorder, no vibration, low noise and minor dust occurred
- Tiny volume, easy to change grinding wheel
|
Rods Precision Cutting Off And End Surface Grinding Machine |
- Suitable to work piece requiring precise cutting cross section such as mold, round pin or stainless steel piece
- Cut and grind the work piece in one step; the working time is short and cutting section angle is precise
- Apply fast clipping jig, clipping process is fast and convenience
- Fine-tuned caliper to make quick dimension positioning task
- To trim grinding wheel, able to timely fine-tune and dimension is unchanged
- High stability, low wearing rate and long operation lifetime
|
Precision External Grinding Machine |
- The high precision grinding machine applies coreless clipping mechanism, fast to position and high machining precision derived
- Twin roller device to clip and grind long pin and punch head
- Applies the attached grinding wheel former to trim wheel angle and arc into special shapes
|
Precision Internal Grinding Machine |
- The high precision grinding machines applies coreless clipping mechanism, fast to position and high machining precision derived
- Twin roller device to clip and grind long pin and punch head
|
Precision Grinding Machine |
- Low friction interface
- Stress relief to cast pieces
- Standard embossing surface
|
Flange K250 |
- K250 grinding wheel fange can be applied to JIANDE grinding machine spindle
|
Flange K350 |
- K350 grinding wheel fange can be applied to TATUNG grinding machine spindle
|
Flange K450 |
- K450 grinding wheel fange can be applied to USA standard grinding machine spindle
|
Wheel Balancing Stand |
- Precise bearing is equipped to pulley spindle
- The sensitivity is within 0.3g
- Pulley surface hardness is above HV620, with co-axial grinding made
- The maximum outer diameter of grinding wheel under trim is 16″
|
Level Balancing Stand |
- Precise level gauge is equipped on main body
- User can rapidly and precisely adjust level status merely by adjusting two screws
- The maximum outer diameter of grinding wheel under trim is 8″
|
Electrode Holder |
- RA 100 is a copper-free pole rod
- User can weld up required copper pole into it and use
- Dust-suppression ring is attached to the stem, guarantee for 3R connector
- HF treatment on stem, high anti-erosion capability derived
|
Electrode Holder |
- RA20-80 is a copper pole rod; the pole is made by high purity red copper; user can machine the pole to required the shape and perform EDM operation
- Dust suppression ring is attached to the stem, guarantee for 3R connector
- HF treatment on stem, high anti-erosion capability derived
|